Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
Are you currently looking for critical information concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't exactly rocket science, yet it does require strong plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately difficult job. If the old tub is readily accessible, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and place the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require a helper to vacate the old tub and embeded in the brand-new one. Make certain you have certified on your own for the job and fit attempting it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This post will aid you set up a new tub in your restroom if you have actually already bought a brand-new tub as well as don't require to change the setup of your previous water supply pipes.
Your devices as well as product checklist need to make up the following:
Getting ready for the Installment
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you must do is detach the water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted access that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before moving on to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wooden boards are valuable in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the tub until the level checks out level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Switch on the water system as well as examine all joints as well as new pipework for leakages and tighten them if necessary. Load the tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been used at the very least once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in place between the faucet and the sink. Protect the tap in place with the supplier offered backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall between the bath and also the tiling, bring about complications with moisture as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that write-up on How to Install a Bathtub from an acquaintance on our other web address. Do you know another person who is enthusiastic about the topic? Feel free to promote it. I am grateful for your time. Visit us again soon.
Click For More Information Report this page